Small 1-Hole Hanger - 1 1/8 Long And 9/16 Wide - Supports 3 Lbs

Product Description

About One Hole Small Hanger • Small One Hole Hanger for Wood Frames. • 1 1/16" Long x 9/16" Wide. • Strap part only is 3/8" wide. • Includes #6 x 3/8" screws. • Holds up to 3 pounds. • Can be used as the art hanger or in conjunction with wire. • These low-profile hangers are less obtrusive than bulky screw eye hangers used to attach the wire to art. Instructions 1) Lay the frame face down on a blanket or soft surface. 2) Hangers should be installed on the frame side rails, between one-quarter and one-third of the way down from the top of the frame. 3) Measure and mark this distance equally both side rails. 4) Pre-drill holes for the hanger mounting screws, being careful not to drill through the front of the frame. 5) Attach the hangers.

About One Hole Small Hanger

• Small One Hole Hanger for Wood Frames.

• 1 1/16 Long x 9/16 Wide.

• Strap part only is 3/8 wide.

• Includes #6 x 3/8 screws.

• Holds up to 3 pounds.

• Can be used as the art hanger or in conjunction with wire.

• These low-profile hangers are less obtrusive than bulky screw eye hangers used to attach the wire to art.

Instructions

1) Lay the frame face down on a blanket or soft surface.

2) Hangers should be installed on the frame side rails, between one-quarter and one-third of the way down from the top of the frame.

3) Measure and mark this distance equally both side rails.

4) Pre-drill holes for the hanger mounting screws, being careful not to drill through the front of the frame.

5) Attach the hangers to the frame with screws. Appropriate screw length will depend on thickness of the frame and weight of the picture.

6) Attach picture wire to the hangers. Appropriate wire size will depend on weight of the picture.

7) Leave enough slack in the wire so that when it is pulled taut up against the back of the frame, the center point of the wire reaches about half the distance between the hanger position and the top of the frame.

8) Hang the picture on a hook.

keyhole hanger used with picture frames and framed mirrors, provides secure hanging

Premium Quality Key Hole Hanger 10 Pack with 3/8 x 4 Gauge Flat Head Phillips Screws

Perfect for use in the garage, workshop, tool shed, basement and throughout the home. Easy to follow instructions on label. Padded arm helps protect your items.

50 lbs. 2-in-1 Heavy-Duty Wall-Mounted Padded Steel Shelf Hanger and Tool Holder (4-Pack)

Sigma's One Hole EMT Straps are used for providing support for steel EMT conduit as required by the National Electric Code (NEC). These zinc-plated steel straps snap onto the conduit for easy installation.

Sigma Electric ProConnex 1-in One-Hole Strap Conduit Fittings (5-Pack)

Available in either single or double keyhole designs. Made from 1/16'' thick plated steel Includes two keyhole fittings with mounting screws

Keyhole Fitting - Single 5/8 x 1-21/32 (2 per Pack)

Front Hanger for 2 Wide Slipper Springs - 3-9/16 Tall - 9/16 Bolt Hole

Front Weld on Hanger for 2 Wide Slipper Springs 3-9/16 Tall - 9/16 Bolt Hole

Keyhole Hanging Plate Heavy Duty 1-3/4''x 11/16'' Single Hole Hook

Pipe strap, Support pipe to wall or ceiling

1 Bracket for Closet Rod/shelf J Series 3/8 Thick X 1-1/2 Wide

Simpson Strong-Tie ITS Galvanized Top-Flange Joist Hanger for 1-3

Small Strap Hanger - 1/78-Inch Long And 3/8-Inch Wide - Picture

Commercial Electric #3 Conduit Hanger FACHS-3-1 - The Home Depot

Wide 1-Hole D-Ring - 1 3/4 Long x 1 Wide - Supports 25 Lbs

Oatey 1-1/4 in. Galvanized 2-Hole Pipe Hanger Strap (4-Pack) 33545

Keyhole Hanging Plate Heavy Duty 1-3/4''x 11/16'' Single Hole Hook